MPC8280 based SBC

The Custom SBC is based on Freescale MPC8280

• Clock Frequency – 333 MHz
• Available in three variants – Commercial, Air Cooled, Conduction Cooled
• Vibration, Shock resistant
• SDRAM Memory – Up to 256 MB
• User Flash Memory –64 MB
• DPRAM – 1 KB
• Two channels programmable for RS-422/RS-232
• One channel RS-232 serial bus interface
• One USB 2.0 Compliant USB Interface
• Two Ethernet ports, 10/100 Mbps
• Physical Size : 118.4 mm x 124.0 mm

MPC8280 based SBC

The Custom SBC is based on Freescale MPC8280

• Clock Frequency – 333 MHz
• Available in three variants – Commercial, Air Cooled, Conduction Cooled
• Vibration, Shock resistant
• SDRAM Memory – Up to 256 MB
• User Flash Memory –64 MB
• DPRAM – 1 KB
• Two channels programmable for RS-422/RS-232
• One channel RS-232 serial bus interface
• One dual redundant MIL-STD-1553B channel
• One USB 2.0 Compliant USB Interface
• Two Ethernet ports, 10/100 Mbps
• Physical Size : 118.4 mm x 124.0 mm

MPC7457 based SBC

• 6U Single Slot Card
• Based On MPC860T processor from Freescale
• Embedded 32-bit PowerPC™ Core
• L1 and L2 cache- 512KB
• Up to 2 MB- L3 cache
• Processor core frequency – 1 GHz
• Available in two variants –Industrial, Conduction Cooled
• Front and Rear I/O connectivity options
• DDR SDRAM Memory – 512 MB/1 GB
• User Flash Memory – Up to 256MB
• Non Volatile RAM – 32 KB
• 32MB System Flash
• One 10/100 Ethernet Port
• One Gigabit Ethernet Port
• Ultra SCSI interface
• Two USB ports Rev2.0
• Four 32-bit Timer counter
• Battery backed RTC
• Four Asynchronous/Synchronous serial ports
• 6 Digital I/O channels
• One PMC site
• P0-P0 back plane overlay board
• Linux, RT-Linux, VxWorks, LynxOS available

MPC860T Based CPU CARD

• 6U Single Slot Card
• Based On MPC860T processor from Freescale
• Embedded 32-bit PowerPC™ Core
• 4Kbyte Instruction Cache
• 4Kbyte Data Cache
• Operates up to 80MHz
• One 10/100Mbps Ethernet Port
• One RS232/RS422 Jumper Configurable UART Port
• Three RS422 Serial Ports
• 4Mbyte SRAM Module
• 2Mbyte Flash Module
• 16Kbyte Non Volatile SRAM
• Two XCV300 FPGA on-board mapped to processor
• Two 4Kbyte FIFO Interfaced to FPGA
• One 64Kbyte x 8 High Speed DPRAM Interfaced to FPGA
• 5V TTL/CMOS Differential Inputs – 20 Nos
• 5V TTL/CMOS Differential Outputs – 15 Nos
• 5V TTL/CMOS Single Ended Inputs – 7 Nos
• Double Euro Form Factor

MC9S12DP512

Traffic Light Controller

• Single Euro Card
• With Two MC9S12DP512 Micro-controllers from Freescale
• One configured as a Master which handles and controls all IOs such as Keypad, LCD, Serial Communication and Ethernet
• Communication
• Other Micro-controller a Slave to the Master which executes Road control logic for sequencing and algorithm execution of
• Traffic Light at the junction
• The card interfaces to a 4 Line character LCD display
• The card interfaces to a 4×4 matrix Keypad
• One 10/100Mbps Ethernet Port
• Eight Numbers of additional Serial ports to communicate to Loop detector cards controlling a Maximum of 16 loops
• One Spartan 3E 250K gate FPGA to execute and control Traffic light drive and Feedback signals to all the roads
• Card Capable of controlling up to eight roads in total
• The Master Micro-controller captures 12 opto-isolated discrete inputs

VPX Single Board Computer based on MPC 8548 (AT-VPX-SBC-MPC8548)

• Freescale MPC8548 PowerQUICC III processor
• Embedded PowerPC e500 core at 1.0 Ghz
• 6U card on VPX backplane
• 1 GB of DDR2 SDRAM with ECC
• NOR Flash Memory – Up to 128 MB
• NAND Flash Memory – Up to 8 GB
• 16 KB Serial EEPROM
• 16 MB NVRAM
• Two Gigabit Ethernet ports
• Two configurable RS232 / RS422 serial port
• Dual PMC / XMC mezzanine sites
• x4 lane PCI express interface at 2.5 Gbps data rate per lane
• x4 lane SRIO interface at 2.5 Gbps data rate per lane
• User Configurable 8 pairs- LVDS I/O
• Real time clock
• Watchdog timer
• Four temperature sensors
• Voltage monitoring
• Multi board Synchronous clock
• Debug port
• Linux, INTEGRITY OS available

VME Single Board Computer ( AT-VME-PADC-MPC8548)

• 6U VME64x single slot module
• Based on Freescale MPC8548 PowerPC processor
• e500 Processor Core @ 1 Ghz
• 1 GB of DDR2 SDRAM with ECC
• 128 MB NOR flash (Program Memory)
• 1GB NAND flash (Storage/Application Memory)
• 1 MB NVRAM
• Two Gigabit Ethernet ports
• Four Multiprotocol RS232/RS422 serial ports
• Two USB 2.0 Host ports (Optional)
• One PMC mezzanine site
• Four Temperature sensors
• Real time clock
• External Watchdog timer and Reset Generator
• Voltage monitoring and power sequencer
• On-board Flash FPGA
• Analog-to-Digital Conversion Block